How to Compile the Linux Kernel

It should be noted that the default kernel that ships with Salix will work in most cases, and no recompiling is necessary. You should only recompile if:

  • Your system’s hardware is not supported by the default kernel
  • You need (want) features only available in a newer kernel
  • To get an extra fraction of a percent hardware performance
  • For fun

Before going ahead, it may be easier (and will in many cases be sufficient to solve the problem) to install the kernel from Slackware current, which will always be relatively recent.

The procedure is actually quite simple, as long as you remember to reinstall the bootloader before rebooting. However, it can take a long time.

Download the kernel source

You may either compile a completely new kernel from source, or recompile the kernel that is packaged by Salix with new configuration.

New kernel from kernel.org

First, download the appropriate kernel source from http://www.kernel.org

You will need the full kernel source tarball (the one with the tar.xz extension).

Unpack source into a directory of your choosing (any directory will do, preferably somewhere in your home directory).

Already installed kernel

Alternatively, you could rebuild the already installed kernel. For that, you will need to install the kernel-source package, if you don’t have it already:

sudo slapt-get -i kernel-source

The kernel source will then be in /usr/src/linux-3.2.25 (change 3.2.25 to the appropriate version.

Preparation

Move to the directory that the kernel source is and run:

make mrproper

This is a cleaning procedure and will set everything to default. You can work from here, but it is highly recommended to use the working configuration (i.e. the one you’ve been running on). The default kernel config is found in /proc/config.gz, so copy this file:

zcat /proc/config.gz > .config

Next, you can configure your kernel. The advantage of using the working configuration as a starting-point is you can leave nearly all the options just as they are, but it may be that you need to turn on support for the hardware that doesn’t work with the existing kernel; or it may work with the new kernel without changing anything at all. To build the kernel with the working configuration unchanged, do:

make oldconfig

If you do need to change anything, there is a choice of interfaces for the configuration. To use a graphical interface, do:

make gconfig

for the gtk-based config, or on a KDE system

make xconfig

for a qt interface.

make menuconfig

will bring up the ncurses based menu-driven config, which will work even if you’re not running X.

The number of different options may appear bewildering, but pretty much all of them can (indeed should) be left unchanged from the working configuration. If in doubt, as a rule of thumb, it is probably best to leave it as is.

Compiling

Once you have configured the kernel to your liking, save and exit. Then do:

make

to build the kernel. This will take some hours…

Installing

After it’s done, do:

sudo make modules_install

to install all of the modules. All of the modules will be installed under /lib/modules/version, where version corresponds to the release number of the kernel compiled.

Next, copy the created kernel image and system map to the boot directory.

sudo cp -v arch/x86/boot/bzImage /boot/vmlinuz-version
sudo cp -v System.map /boot/System.map-version

where version corresponds to the release number of the kernel compiled.

Assuming the kernel in your working system is the standard one that came with Salix, the new one you just built will also be a ‘huge’ kernel that doesn’t need an initrd, so you can omit the next step.

initrd

However, if you know you do need to create an initrd.gz file:

/usr/share/mkinitrd/mkinitrd_command_generator.sh -l /boot/vmlinux-version

will generate a mkinitrd command that you can then copy and paste. By default, it will output to /boot/initrd.gz. You may want to change this when cutting and pasting so that it will output to /boot/initrd-version.gz. Note that a suggested lilo stanza is also created, but the initrd itself is only made when you run the mkinitrd command itself. To do so, root privileges are required.

Refresh LILO

As a final step, edit /etc/lilo.conf so that it will see the newly created kernel, including the ‘initrd’ line only if you created one:

image = /boot/vmlinuz-version
root = /dev/sda6
initrd = /boot/initrd-version.gz
label = "New Kernel"
read-only

Don’t forget to run:

sudo lilo

to take effect of the new configuration; or use whichever tool you prefer to install the bootloader.

That’s it. When you reboot, you should see the new kernel in the lilo menu, and everything should work. As a check, after the system reboots itself: uname -a

You should see that the kernel release number is indeed the version you just built.

The old kernel is still present, and your bootloader will still include an option to boot with it as a fallback. Once you are certain everything is working properly with the new one, you may wish to remove the old entry from the bootloader and (optionally, with care) delete the old kernel in /boot.